DCPro Switch-Mode Cathodic Protection Rectifier (30V/20A & 50V/50A)

The DCPro is a switch-mode cathodic protection rectifier available in 30V/20A and 50V/50A sizes, replacing tap-changing units with 80–90% efficient, pure DC constant-current output adjustable in 0.1 A steps. Auto-ranging 115–240 VAC input, aluminum or steel cabinet or chassis-only, built-in RMU and interrupter interface, ETL certified, 3-year warranty.

Attachments

  • The DCPro Cathodic Protection Power Supply is a durable, switch-mode power supply that provides clean, efficient DC power. With the look of a conventional rectifier, the DCPro requires no computer interface and no confusing menus to navigate. Engage the main breaker and turn the single control knob to adjust the current output.

    A bright colour display, readable in direct sun, presents both analog and digital output voltage and current levels, with a message window for additional operational messages. With the DCPro, very specific output ratings are no longer required to overcome output adjustment limitations.

    DCPro switch-mode cathodic protection rectifier

    Features

    • Simple to operate — one knob, no computer interface and no menus
    • Constant current output control in 0.1 amp steps
    • Pure DC output with no AC ripple
    • High operating efficiency of 80 to 90%
    • Fully solid-state “switch-mode” operation
    • Operates on any single-phase power from 115 to 240 VAC without primary tap changes
    • Rejects induced AC
    • Operates up to 55 °C with over-temperature sensors and protection
    • Standard AC & DC surge protection
    • Analog and digital output and status display, readable in direct sun
    • Test points for cross-checking meter accuracy
    • Built-in interrupter interface
    • Pre-wired RMU terminal strip
    • Built-in 12-volt DC power supply for RMU and portable interrupter
    • 115 VAC convenience outlet with GFI protection
    • Dead-front safety panel and side shields
    • Lightweight component chassis
    • Standard 3-door aluminum enclosure
    • Two power output choices eliminate the need for an exact power output rating
    • ETL Certified

    Applications

    Pipelines. Constant-current control keeps transmission and distribution pipelines within protection criteria as soil resistivity changes along the right-of-way, and induced-AC rejection suits HVAC-corridor installations.

    Above-ground storage tanks. Clean, adjustable DC for tank-bottom protection with grid or distributed anode systems, where precise current settings and accurate potential surveys matter.

    Underground plant, well casings, and buried structures. Universal AC input and a compact footprint simplify installation at compressor stations, refineries, water treatment facilities, and well sites.

    Marine and submerged structures. Reliable, ripple-free output for docks, sheet pile, intake structures, and other submerged steel where legacy rectifiers are reaching end of life.

  • The following provides the ordering details for the two output sizes available: 30 volt – 20 amp and 50 volt – 50 amp. With the precise control standard on the DCPro, there is no need to order the exact DC output level you would with a standard rectifier. If you needed a 40-30 rectifier, you can now order a 50-50 DCPro and dial in the exact power output you need. The DCPro also ships from stock, avoiding weeks of waiting.

    Model CodeFarwest Item No.DC OutputWeight (lb)Cabinet Type
    FSMA 30-20 ALPC17-6500030V-20A87Aluminum, powder-coated white
    FSMA 30-20 STPC17-6500230V-20A102Steel, powder-coated white
    FSMA 30-20 XX17-6510030V-20A17Power supply chassis only. No cabinet.
    FSMA 50-50 ALPC*17-6505050V-50A or (2x) 50V-25A135Aluminum, powder-coated white
    FSMA 50-50 STPC*17-6505250V-50A or (2x) 50V-25A170Steel, powder-coated white
    FSMA 50-50 XX*17-6515050V-50A or (2x) 50V-25A45Power supply chassis only. No cabinet.

    All models accept 115–240 VAC, single phase, 47–63 Hz.

    *The DCPro in the 50-volt, 50-amp output configuration can easily be field configured to provide controlled current to two separate structures.

    Sizing Guidance

    The DCPro was designed and built as a “two sizes fits most” approach, which may provide a solution for approximately 80% of cathodic protection demand. If a customer requires more output current, the DCPro may not be the solution. However, DCPro units can be linked together to double the output DC voltage — two 30 volt, 20 amp power supplies can be made to achieve 60 volts and 20 amps if required.

  • Technical Specifications

    The DCPro is offered in two output sizes. Because output is adjustable in 0.1 A steps, there is no need to specify an exact rating the way you would with a conventional tap-changing rectifier — size up and dial in.

    Available ModelsFSMA 30-20 (30V–20A) and FSMA 50-50 (50V–50A)
    Dual-Output OptionFSMA 50-50 can be configured as two independent 50V–25A outputs for two separate structures
    Output TypePure DC, no AC ripple; fully solid-state switch-mode conversion
    Control ModeConstant current; single-knob adjustment in 0.1 A increments
    AC Input115–240 VAC single-phase, 47–63 Hz, auto-configuring (no primary taps)
    Efficiency80–90% power conversion
    Ambient Operating TemperatureUp to 55 °C (131 °F) with over-temperature sensing and protection
    ProtectionAC and DC surge protection (standard); over-temperature protection; induced-AC rejection
    Display & MeteringColour display readable in direct sun; analog and digital voltage and current readouts; message window; test points for meter verification
    Remote Monitoring InterfacePre-wired 7-position RMU terminal block; built-in 12 VDC supply for a customer-supplied RMU
    Interrupter InterfaceBuilt-in; electronic interruption via RMU or portable interrupter (12 VDC supplied)
    Cabinet OptionsAluminum (ALPC) or steel (STPC) powder-coated cabinet, or chassis only (XX) for installation in an existing rectifier enclosure
    WeightsFSMA 30-20: 87 lb aluminum / 102 lb steel / 17 lb chassis. FSMA 50-50: 135 lb aluminum
    CertificationETL Certified
    Warranty3 years from date of purchase

    Full model codes, Farwest item numbers and cabinet types are listed under the Models & Ordering tab.

    DCPro vs. Conventional Tap-Changing Rectifiers

    Most cathodic protection rectifiers in service today are still transformer-based designs with coarse and fine tap bars. Here is how the DCPro compares.

    FeatureConventional Tap-ChangerDCPro Switch-Mode
    Output adjustmentMove coarse and fine tap links with power off; discrete steps onlyTurn one knob, live, in 0.1 A increments
    RegulationConstant voltage; current drifts as circuit resistance changesConstant current; output held automatically
    EfficiencyLower, with the difference lost as transformer and stack heat80–90%
    Output qualityRectified AC with significant ripple unless filteredPure DC, no AC ripple
    AC inputPrimary taps must match site voltageAuto-ranging 115–240 VAC
    Induced ACCan disturb operation and readingsRejected by design
    SizingMust order close to the exact output neededSize up and dial in; fewer part numbers to stock
    Lead timeOften weeksShips from stock
    Upgrade path—Chassis-only option fits existing enclosures
  • Frequently Asked Questions

    Is the DCPro a rectifier or a power supply?

    Both. In cathodic protection the terms are used interchangeably. The DCPro does the same job as a traditional CP rectifier — converting AC to DC to drive an impressed current anode system — but uses solid-state switch-mode conversion instead of a transformer and tap bars.

    What output sizes are available?

    Two: the FSMA 30-20 at 30V–20A and the FSMA 50-50 at 50V–50A. The 50-50 can also be configured as two independent 50V–25A outputs to protect two separate structures from one unit.

    Do I need to order an exact output rating?

    No. Because output is adjustable in 0.1 A steps, you size up rather than matching exactly. If you would have ordered a 40-30 conventional rectifier, order a 50-50 DCPro and dial in the output you need.

    Can the DCPro replace my existing rectifier without a new enclosure?

    Yes. Order the chassis-only (XX) version, which is sized to slide into a standard rectifier enclosure, so you can modernize a site without new pole or pad work. Complete aluminum and steel cabinets are also available.

    Does the DCPro work with my remote monitoring unit (RMU)?

    Yes. It includes a pre-wired 7-position RMU terminal block and a built-in 12 VDC supply to power a customer-supplied RMU, plus a built-in interrupter interface for electronic interruption during surveys.

    What input voltage does it need?

    Any single-phase supply from 115 to 240 VAC at 47 to 63 Hz. The unit configures itself automatically; there are no primary taps to set.

    Is it constant current or constant voltage?

    The DCPro is a constant-current design. You set the protective current and the unit holds it as circuit resistance changes with soil moisture, coating condition or season.

    What warranty and certifications does it carry?

    The DCPro is ETL Certified and covered by a three-year warranty from the date of purchase.

Customers Who Viewed This Also Viewed
Ultrasonic Digital Thickness Gauge, Model 1/Ex Advanced Intrinsically Safe UTG by Cygnus
Ref-Check VPR (Voltage Potential Restoration) Test Instrument by Farwest Corrosion
Wire Reel with Submersible Adapter by Farwest Corrosion
H35 Gray Tape Cold-Applied Coating by Tapecoat
Testox Metallic Test Stations by Gerome